Fuji Xerox Phaser 5500 Service Manual Download Page 308

Page: 308 / 623

3-230

Phaser 5500 Printer Service Manual

Stacker Lower Tray Failure

The Stacker No Paper Sensor does not change state within the time specified
following the Stacker Lower Tray beginning to lower.

Cycle the printer power.
Does the error still occur?

Go to Step 3.

Problem solved.

Replace the Finisher Main PWB.
Does the error still occur?

Replace the
Engine Logic
Board
(page 8-89).

Problem solved.

Lower Tray Failure (No Paper Sensor) Troubleshooting Reference

Applicable Parts

References

■

Finisher Main PWB

■

Sensor Actuator

■

Stacker No Paper
Sensor

■

Main Sensor
Harness

■

Elevator Motor

■

Engine Logic
Board.

■

Print Engine P/J Engine Logic Board (page 10-13)

■

PL8.1 Print Engine Electrical (page 9-40)

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Sensors (2/2) Wiring (page 5-41)

■

Finisher Clutch and Solenoids (page 5-43)

■

PL25.6 Finisher Stack (page 4-54)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Lower Tray Failure (No Paper Sensor) Troubleshooting Procedure

Step

Actions and Questions

Yes

Check the lower part of the Stacker for
obstacles.
Are there any obstacles on the lower
part of the Stacker Tray?

Remove any
obstacles.

Go to Step 2.

Check the Actuator installation.
Does the Actuator enter the Upper Limit
sensor sensing area?

Repair the
Actuator.

Go to Step 3.

Check the Stacker No Paper Sensor.
Run the Service Diagnostics Stacker No
Paper Sensor test.
Does the sensor state change when the
sensor is blocked?

Go to Step 9.

Go to Step 4.

Staple Set Over Count Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands