Fuji Xerox Phaser 5500 Service Manual Download Page 161

Page: 161 / 623

Error Messages, Codes, and Procedures

3-83

Jam at D - C8-6 Duplex

Paper remains at Duplex Unit’s Wait Sensor located behind Door D.

Applicable Error Code

Jam at D - C8-6 Duplex

Check the Main Harness for continuity.

1. Disconnect PF57 and JF06.

2. Check for continuity at the following:

PF57-7 <=> JF06-11
PF57-6 <=> JF06-8
PF57-5 <=> JF06-9
PF57-4 <=> JF06-10
PF57-3 <=> JF06-12
PF57-2 <=> JF06-7

Are these conductive?

Go to Step 30.

Repair the Main
Harness.

Check the Take Away Motor resistance.
Is there some amount of resistance
across JF57-3/4(COM) and JF57-1/2/5/6?

Go to Step 31.

Replace the Take
Away Motor
(page 3-64).

Check for +24 V to the Take Away Motor.
Is there +24 V across PF06-9 <=> PF04-
3, and PF06-10 <=> PF04-3 on the PWB?

Go to Step 32.

Replace the
Tray 6 PWB
(page 3-67).

Replace the Take Away Motor.
Print a Test Print.
Does the error still occur?

Go to Step 33.

Problem solved.

Replace the Tray 6 PWB.
Print a Test Print.
Does the error still occur?

Replace the
Engine Logic
Board
(page 8-89).

Problem solved.

Jam at D (Wait Sensor) Troubleshooting Reference

Applicable Parts

References

■

Wait Sensor

■

Duplex Unit PWB

■

Engine Logic
Board

■

Print Engine P/J Engine Logic Board (page 10-13)

■

PL8.1 Print Engine Electrical (page 9-40)

■

Phaser 5500 Printer Options Service Manual

■

Duplex Unit Plug/Jack Locator (page 5-12)

■

Duplex Unit Wiring (page 5-13)

■

PL23.1 Duplex Unit (page 4-34)

Jam at Tray 6 (Feed Out Sensor #6) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands