manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 42

2-2

Phaser 5500 Printer Service Manual

Phaser 5500 Operational Overview

The Phaser 5500 base configuration combines a dual-pass, monochrome laser print 
engine with a multi-purpose Tray 1/MPT and two universal media trays, trays 2 and 3. 
The Standard Output Tray holds 500 sheets facedown. Phaser 5500 options add 
memory, paper capacity, and functionality. For models not originally equipped, a 20 
GB Hard Drive is available. A selection of memory upgrades can raise the installed 
RAM to the 512 MB maximum. Additional paper capacity is also available. Trays 4 
and 5 (1000-Sheet Feeder) when installed, add two 500-sheet universal media trays. 
An optional high-capacity 2000-Sheet Feeder (Tray 6) brings the maximum paper 
capacity to 4,100 sheets. An Envelope Tray, replacing Tray 2, holds up to 35 
envelopes. On the output side, 3500 sheet stapler/punch/stacker is available.

This section focuses on the printer’s operational characteristics providing detailed 
descriptions of the paper path, sensors, xerographics and major system assemblies. 
Operational details of the available options appear in Book 2, Phaser 5500 Printer 
Options Service Manual.

Summary of the Printing Process

The illustration below shows the orientation of the major components associated with 
the xerographics process as viewed from the front of the printer.

Fuser

Drum Cartridge

Paper
Transport

Laser Beam

Magnetic Roller

Charge Metering Blade

Cleaning
Blade

Detack Saw

Paper

Drum

BCR

Pressure
Roller

Heat Roller

s5500-015

Transfer Roller

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands