Fuji Xerox Phaser 5500 Service Manual Download Page 555

Page: 555 / 623

Wiring Diagrams

10-5

420

C-212

Connects the Engine Logic Board and LV PWR Harness.

421

C-213

Connects the Engine Logic Board and LV PWR Harness.

430

H-120

Connects the Exit PWB and LV PWR Harness.

431

H-120

Connects the Exit PWB and LV PWR Harness.

432

H-120

Connects the Exit PWB and EXIT Harness.

433

I-120

Connects the Exit PWB and EXIT Harness.

434

I-120

Connects the Exit PWB and EXIT Harness.

490

I-121

Connects the Flash ROM device to the I/P Board.

500

C-110

Connects the HVPS and Registration Harness.

521

I-246

Connects the LVPS and LV PWR Harness.

525

I-247

Connects the LVPS and LV PWR Harness.

526

I-245

Connects the LVPS and LV PWR Harness.

540

E-122

Connects the Hard Drive to the I/P Board.

590

J-123

Connects the I/P Board and Engine Logic Board.

600

A-139

Connects the Fuser and Fuser AC Harness.

600

H-196

Connects the Fuser and Fuser Harness.

601

C-183

Connects the Tray 2 Feeder Harness and Feeder Harness.

602

C-184

Connects the Tray 3 Feeder Harness and Feeder Harness.

605

I-199

Connects the Tray 1/MPT and Tray 1/MPT Harness.

606

G-195

Connects the EXIT 2 Harness and EXIT Harness.

607

G-199

Connects the Fuser Harness and PH Harness.

608

C-184

Connects the Take Away Sensor Harness and PH Harness.

609

D-151

Connects the Tray 1/MPT Sensor Harness and Tray 1/MPT Harness.

610

B-109

Connects the ATC Sensor and Registration Harness.

613

G-196

Connects the OCT Harness and EXIT Harness.

830

C-125

Connects the RAM DIMM to the I/P Board.

831

C-125

Connects the RAM DIMM to the I/P Board.

890

I-125

Connects the I/P Board to the Laser Assembly.

Print Engine Plug/Jack Designators

P/J

Coordinates Remarks

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands