Fuji Xerox Phaser 5500 Service Manual Download Page 491

Page: 491 / 623

FRU Disassembly

8-81

Offset Home Position Sensor

Remove the Upper Rear Cover (page 8-15).

Remove the Top Rear Cover (page 8-6).

Open Door A.

Remove the Exit 1 Top Cover (page 8-18).

Open the Front Door.

Remove the Front Left Cover (page 8-5).

Remove the Exit Transport Assembly (page 8-78).

PL6.2.5

Remove the Exit 1 Offset Motor.

Remove the two screws securing the sensor bracket to the Exit Transport
Assembly.

10.

Release the three hooks securing the Offset Home Position Sensor to the sensor
bracket.

11.

Remove the Offset Home Position Sensor.

Offset Home
Position Sensor

Hooks

Hook

Sensor Bracket

Exit Transport Assembly

s5500-170

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands