Fuji Xerox Phaser 5500 Service Manual Download Page 438

Page: 438 / 623

8-28

Phaser 5500 Printer Service Manual

Tray 2 and 3 Pre-Feed Sensor

Remove the Tray 1/MPT Rear Cover (page 8-16).

Remove the Tray 1/MPT Feeder (page 8-32).

Remove Door A (page 8-46).

Remove the Take Away Bracket (page 8-40).

Remove the Tray 2 Feeder (page 8-20) or Tray 3 Feeder (page 8-21).

PL2.3.15

Remove the Pre-Feed Sensor from the Front Chute as shown in the figure.

Disconnect the connector from the Pre-Feed Sensor.

Feeder

Pre Feed Sensor

s5500-111

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands