manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 239

Error Messages, Codes, and Procedures

3-161

Stacker Lower Tray Failure (Stack Height Sensors) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Check the Stacker Lower Tray vertical 
transport and belts for obstacles and 
deformation.
Are there obstacles or belt wear in the 
vertical transport mechanism?

Remove 
obstacles/replace 
deformed part.

Go to Step 2.

2

Check the Actuator installation.
Does the Actuator enter the Upper Limit 
sensor sensing area?

Go to Step 3.

Repair the 
Actuator.

3

Test the Lower Tray No Paper Sensor.
Run the Service Diagnostics Lower Tray 
No Paper Sensor test.
Does the sensor state change when the 
sensor is blocked?

Go to Step 9.

Go to Step 4.

4

Check the Lower Tray No Paper Sensor 
Harness connection.
Are P/J8326 and P/J8302B connected?

Go to Step 6.

Connect and go 
to Step 5.

5

Print a Test Print.
Does the error still occur?

Go to Step 6.

Problem solved.

6

Check the Lower Tray No Paper Sensor 
Harness continuity.

1. Disconnect P/J8326 on the Lower Tray 

No Paper Sensor Harness, and P/
J8302B on the Finisher Main PWB.

2. Check for continuity at the following:

P/J8326-3 <=> P/J8302B-15
P/J8326-2 <=> P/J8302B-16
P/J8326-1 <=> P/J8302B-17

Are these conductive?

Go to Step 7.

Repair the Lower 
Tray No Paper 
Sensor Harness. 
If problem 
persists, go to 
Step 7.

7

Check for +5 V to the Lower Tray No Paper 
Sensor.
Is there +5 V across J8302B-17 <=> 
J8302B-15 on the Finisher Main PWB?

Go to Step 8.

Replace the 
Finisher Main 
PWB 
(page 3-248).

8

Check Stacker Lower Tray No Paper 
Sensor.
Does the voltage across P8302B-16 <=> 
P8302B-15 on the Finisher Main PWB 
change when the sensor is blocked?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Replace the 
Lower Tray No 
Paper Sensor 
(page 3-143).

9

Test the Elevator Motor.
Run the Service Diagnostics Stacker Motor 
Up and Down tests alternately.
Does the Elevator Motor operate?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Go to Step 10.

10

Check the Elevator Motor connection.
Is P/J8305 connected to the Finisher 
Main PWB?

Go to Step 12.

Connect and go 
to Step 11.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands