manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 178

3-100

Phaser 5500 Printer Service Manual

7

Check Entrance Sensor signal.
Does the voltage across P8302A-2 <=> 
P8302A-1 on the Finisher Main PWB 
change when the sensor is blocked?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Replace the 
Entrance Sensor 
(page 3-217).

8

Check the Transport Motor.
Run the Service Diagnostics Transport 
Motor test.
Does the motor rotate normally?

Go to Step 9.

Go to Step 10.

9

Test Entrance Roller drive.
Run the Service Diagnostics Transport 
Motor test.
Do the Entrance Rollers rotate?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Restore Roller 
operation.

10

Check Main Drive Harness connections.
Are P/J8342 and P/J8304 connected?

Go to Step 12.

Connect and go 
to Step 11.

11

Print a Test Print.
Does the error still occur?

Go to Step 12.

Problem solved.

12

Check Main Drive Harness continuity.

1. Disconnect P/J8342 and P/J8304.

2. Check for continuity at the following:

J8342-1 <=> J8304-23
J8342-2 <=> J8304-16
J8342-3 <=> J8304-25
J8342-4 <=> J8304-27
J8342-5 <=> J8304-18
J8342-6 <=> J8304-29

Are these conductive?

Go to Step 13.

Repair the Main 
Drive Harness.

13

Check Transport Motor resistance.
Is there some amount of resistance 
across P8342-2/5(COM) and P8342-1/3/
4/6?

Go to Step 14.

Replace the 
Transport Motor 
(page 3-222).

14

Check for +24 V to the Transport Motor.
Is there +24 V across J8304-16 <=> 
ground, and J8304-18 <=> ground on 
the Finisher Main PWB?

Go to Step 15.

Replace the 
Finisher Main 
PWB 
(page 3-248).

15

Replace the Transport Motor.
Print a Test Print.
Does the error still occur?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Problem solved.

Static Jam at F (Transport Entrance Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands