manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 303

Error Messages, Codes, and Procedures

3-225

Stapler is Empty - Staple Pin Warning

The Low Staple Sensor in the Staple Cartridge indicates no staples remain.

Stapler is Empty (Low Staple Sensor) Troubleshooting Reference

Applicable Parts

References

■

Finisher Main PWB

■

Staple Harness

■

Stapler Assembly

■

Engine Logic 
Board.

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Staple P/J Locator (page 5-30)

■

Finisher Stapler Wiring (page 5-45)

■

PL25.8 Finisher Staple (page 4-58)

■

PL25.14 Finisher Electrical (page 4-70)

Stapler is Empty (Low Staple Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Test the Low Staple Sensor.
Run the Service Diagnostics Staple Head 
Low Staple Sensor test.
Does the sensor state change when the 
Staple Cartridge is removed or 
replaced?

Go to Step 9.

Go to Step 2.

2

Check the Staple Cartridge for faulty parts 
and foreign particles.
Are there damaged parts or foreign 
particles?

Replace faulty 
parts or clean as 
needed.

Go to Step 3.

3

Check the Staple Harness connections.
Are P/J8356 and P/J8308 connected?

Go to Step 5.

Connect and go 
to Step 4.

4

Cycle the printer power.
Does the error still occur?

Go to Step 5.

Problem solved.

5

Check Staple Harness continuity.

1. Disconnect P/J8356 and P/J8308.

2. Check for continuity at the following:

P/J8356-1 <=> P/J8308-15
P/J8356-2 <=> P/J8308-14
P/J8356-3 <=> P/J8308-13
P/J8356-4 <=> P/J8308-12
P/J8356-5 <=> P/J8308-11

Are these conductive?

Go to Step 6.

Repair the Staple 
Harness.

6

Check for +5 V to the Low Staple Sensor.
Is there +5 V across J8308-11 <=> 
J8308-15 on the Finisher Main PWB?

Go to Step 7.

Replace the 
Finisher Main 
PWB 
(page 3-248).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands