manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 552

10-2

Phaser 5500 Printer Service Manual

Print Engine Plug/Jack Designators

The Plug/Jack locators consist of the P/J Locator Tables and the P/J Locator 
Diagrams. The table lists the plug/jack numbers in numerical order. The co-ordinates 
column lists the diagram coordinates for the location of the connector. A brief 
description of each connection is included in the remarks column.

Print Engine Plug/Jack Designators

P/J

Coordinates Remarks

1

D-204

Connects the LVPS and Main Switch Harness.

2

D-243

Connects the LVPS and Finisher Outlet.

3

D-245

Connects the LVPS and Heater Harness.

6

E-245

Connects the LVPS and Fuser AC Harness.

7

E-245

Not Connected

11

D-245

Connects the LVPS and GFI Breaker.

12

D-245

Connects the LVPS and GFI Breaker

20

J-141

Connects the Fuser Main Lamp (Heat Rod) and Fuser Harness.

21

J-141

Connects the Fuser Sub Lamp 1 and Fuser Harness.

22

J-141

Connects the Fuser Sub Lamp 2 and Fuser Harness.

50

F-229

Connects the GFI Breaker and LVPS.

56

B-238

Connects the Power Switch and Power Switch Harness.

57

B-239

Connects the Power Switch and Power Switch Harness.

68

B-239

Connects the Power Switch and Power Switch Harness.

69

B-239

Connects the Power Switch and Power Switch Harness.

72

F-230

Connects the GFI Breaker and Ground (Earth).

73

G-230

Connects the Finisher Outlet and LVPS.

74

G-230

Connects the Finisher Outlet and LVPS.

75

G-230

Connects the Finisher Outlet and Ground (Earth).

100

G-180

Connects the Tray 2 Level Sensor and the Tray 2 Feeder Harness.

101

G-180

Connects the Tray 2 No Paper Sensor and the Tray 2 Feeder Harness.

102

G-180

Connects the Tray 3 Level Sensor and Tray 3 Feeder Harness.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands