Fuji Xerox Phaser 5500 Service Manual Download Page 314

Page: 314 / 623

3-236

Phaser 5500 Printer Service Manual

Slide In Tray 6 Feeder - Tray 6 Undocked

The Tray 6 Docking Switch indicates that Tray 6 is separated from the printer.

Check for +24 V to the switch.
Is there +24 V across P/J121-B1 (+) <=>
ground?

Replace the
Switch

Replace the
Engine Logic
Board.

Tray 6 Undocked (Docking Interlock Switch) Troubleshooting Reference

Applicable Parts

References

■

Tray 6 PWB

■

Tray 6 Main
Harness

■

Tray 6 Docking
Switch

■

Engine Logic
Board

■

Print Engine P/J Engine Logic Board (page 10-13)

■

PL8.1 Print Engine Electrical (page 9-40)

■

Phaser 5500 Printer Options Service Manual

■

2000-Sheet Feeder P/J Locator (page 5-20)

■

2000-Sheet Feeder Interface Wiring (page 5-23)

■

PL22.7 Tray 6 Drive and Transportation (page 4-30)

■

PL22.8 Tray 6 Electrical (page 4-32)

Tray 6 Undocked (Docking Interlock Switch) Troubleshooting Procedure

Step

Actions and Questions

Yes

Check the Tray 6 installation.
Is Tray 6 installed correctly?

Go to Step 2.

Correct and go to
Step 2.

Check the Docking Switch condition.
Is the Docking Switch damaged?

Replace the
Docking Switch
(page 3-66).

Go to Step 3.

Test the Docking Switch.

1. Pull Tray 6 away from the printer.

2. Run the Service Diagnostics Tray 6

Interlock Switch test.

Does the sensor status change when
the switch plunger is repeatedly
pushed?

Go to Step 10.

Go to Step 4.

Check Tray 6 Docking Switch Harness
connections.
Are FS003, FS004 and P/JF08
connected?

Go to Step 6.

Connect and go
to Step 5.

Cycle printer power.
Does the error still occur?

Go to Step 6.

Problem solved.

Front Door Open (Front Door Interlock) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands