manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 242

3-164

Phaser 5500 Printer Service Manual

12

Check Lower Tray Upper Limit Sensor 
Sensor Harness continuity.

1. Disconnect P/J8327 on the harness, and 

P/J8302B on the Finisher Main PWB.

2. Check for continuity at the following:

P/J8327-3 <=> P/J8302B-18
P/J8327-2 <=> P/J8302B-19
P/J8327-1 <=> P/J8302B-20

Are these conductive?

Go to Step 13.

Repair the Lower 
Tray Upper Limit 
Sensor Harness.

13

Check for +5 Vto the Lower Tray Upper 
Limit Sensor.
Is there +5 V across J8302B-20 <=> 
J8302B-18 on the Finisher Main PWB?

Go to Step 14.

Replace the 
Finisher Main 
PWB 
(page 3-248).

14

Check Lower Tray Upper Limit Sensor 
signal.
Does the voltage across P8302B-19 <=> 
P8302B-18 on the Finisher Main PWB 
change when the sensor is blocked?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Replace the 
Lower Tray Upper 
Limit Sensor 
(page 3-143).

15

Test the Elevator Motor.
Run the Service Diagnostics Stacker Motor 
Up and Down tests alternately.
Does the Elevator Motor operate?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Go to Step 16.

16

Check the Elevator Motor connection.
Is P/J8305 connected to the Finisher 
Main PWB?

Go to Step 18.

Connect and go 
to Step 17.

17

Print a Test Print.
Does the error still occur?

Go to Step 18.

Problem solved.

18

Replace the Elevator Motor.
Print a Test Print.
Does the error still occur?

Go to Step 19.

Problem solved.

19

Replace the Finisher Main PWB.
Does the error still occur?

Replace the 
Engine Logic 
Board 
(page 8-89).

Problem solved.

Stacker Lower Tray Failure (Upper Limit Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands