Fuji Xerox Phaser 5500 Service Manual Download Page 488

Page: 488 / 623

8-78

Phaser 5500 Printer Service Manual

Exit Transport Assembly

Remove the Upper Rear Cover (page 8-15).

Remove the Top Rear Cover (page 8-6).

Open Door A.

Remove the Exit 1 Top Cover (page 8-18).

Open the Front Door.

Remove the Front Left Cover (page 8-5).

PL6.2.1

Remove the two screws securing the Exit Bracket to the frame.

Remove the Exit bracket.

Replacement Note

Make sure the Stack Full Actuator rotates freely.

s5500-167

Exit Bracket

Door A

Upper Rear Cover

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands