Fuji Xerox Phaser 5500 Service Manual Download Page 434

Page: 434 / 623

8-24

Phaser 5500 Printer Service Manual

Remove the Tray 2 Feeder (page 8-20) or Tray 3 Feeder (page 8-21).

PL2.3.2

Disconnect the connector from the Feed/Lift Motor.

Remove the two Phillips screws securing the Feed/Lift Motor to the Feeder.

Remove the Feed/Lift Motor.

Tray 2 and 3 No Paper Sensor

Remove the Tray 1/MPT Rear Cover (page 8-16).

Remove the Tray 1/MPT Feeder (page 8-32).

Remove Door A (page 8-46).

Remove the Take Away Bracket (page 8-40).

Feeder Assembly

Feed/Lift Up
Motor

Connector

s5500-104

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands