Fuji Xerox Phaser 5500 Service Manual Download Page 554

Page: 554 / 623

10-4

Phaser 5500 Printer Service Manual

202

E-180

Connects the Tray 3 Feed/Lift Motor and Tray 2 Feeder Harness.

204

H-199

Connects the Takeaway Clutch and PH Harness.

205

D-151

Connects the Tray 1/MPT Feed Solenoid and MSI Harness.

206

G-196

Connects the Exit 1 Offset Motor and EXIT Harness.

214

G-198

Connects the Drive Assembly and Drive Harness.

215

E-166

Connects the Registration Clutch and Registration Harness.

216

H-106

Connects the Toner Dispense Motor and LV PWR Harness.

221

E-107

Connects the Engine Logic Board and Drum Cartridge Fan.

311

B-242

Connects the Front Panel and Front Panel Harness.

400

C-214

Connects the Engine Logic Board and LV PWR Harness.

401

C-214

Connects the Engine Logic Board and LV PWR Harness.

402

D-212

Connects the Engine Logic Board and I/P Board Harness.

403

F-211

Connects the Engine Logic Board and Registration Harness.

404

E-212

Connects the Engine Logic Board and Xerographics Harness.

405

G-212

Connects the Engine Logic Board and Interlink Harness.

406

D-212

Connects the Engine Logic Board and Laser Harness.

407

C-212

Connects the Engine Logic Board and Laser Harness.

408

G-211

Connects the Engine Logic Board and Drive Harness.

409

G-213

Connects the Engine Logic Board and Feeder Harness.

410

G-212

Connects the Engine Logic Board and PH Harness.

411

G-214

Connects the Engine Logic Board and Tray 1/MPT Harness.

412

C-213

Connects the Engine Logic Board and Size Harness.

413

D-214

Connects the Engine Logic Board and Tray 4-5 Harness.

414

F-214

Connects the Engine Logic Board and Tray 6 Harness.

415

F-214

Connects the Engine Logic Board and Tray 6 Harness.

416

D-214

Connects the Engine Logic Board and Output Unit.

417

E-214

Connects the Engine Logic Board and Duplex Unit Harness.

419

D-212

Connects the Engine Logic Board and CRUM Harness.

Print Engine Plug/Jack Designators

P/J

Coordinates Remarks

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands