manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 605

Reference

A-21

Exit 2 Solenoid/Clutch Test Menu

Activates the Exit 2 Gate Solenoid. The clicking made by the solenoid when 
energized indicates its condition. 

Tray 4 & 5 Solenoid/Clutch Test Menu

Activates the Take Away Clutch. The clicking made by the clutch when energized 
indicates its condition. 

Tray 6 Solenoid/Clutch Test Menu

Tests the functionality of the optional Tray 6 solenoid. 

Finisher Solenoid/Clutch Tests Menu

Activates the selected clutch or solenoid. The clicking made by the part when 
energized indicates its condition

Exit 2 Solenoid Test

Test

Action / Requirement

Exit Gate Solenoid

Energize the Exit Gate Solenoid. This test runs with Door E open.

Tray 4 & 5 Clutch Test

Test

Action / Requirement

Take Away Clutch

Energize the Take Away Clutch on the optional tray module.

Tray 6 Solenoid/Clutch Tests

Test

Action / Requirement

Nudger (High Power)

Energize the Nudger Solenoid at high power.

Nudger (Low Power)

Energize the Nudger Solenoid at low power.

Finisher Solenoid/Clutch Tests 

Test

Action / Requirement

Buffer Gate Solenoid 
(path out)

Energize the Buffer Gate Solenoid moving the Buffer Gate to direct 
paper over the Buffer Roller.

Buffer Gate Solenoid 
(path-in)

Energize the Buffer Gate Solenoid moving the Buffer Gate to direct 
paper into the Buffer Path.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands