manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 20

xviii

Phaser 5500 Printer Service Manual

Servicing Electrical Components

Before starting any service procedure, switch off the printer power and unplug the 
power cord from the wall outlet. If you must service the printer with power applied, 
be aware of the potential for electrical shock.

Warning

Turning the power off by using the On/Off switch does not completely de-
energize the printer. You must also disconnect the printer power cord from the 
AC outlet. Position the power cord so that it is easily accessible during servicing. 

Warning

Do not touch any electrical component unless you are instructed to do so by a 
service procedure.

Servicing Mechanical Components

When servicing mechanical components within the printer, manually rotate drive 
assemblies, rollers, and gears.

Warning

Do not try to manually rotate or manually stop the drive assemblies while any 
printer motor is running.

Servicing Fuser Components

Warning

This printer uses heat to fuse the toner image to media. The Fuser is VERY HOT. 
Turn the printer power off and wait at least 5 minutes for the Fuser to cool before 
you attempt to service the Fuser or adjacent components. 

S7300-02

S7300-03

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands