Fuji Xerox Phaser 5500 Service Manual Download Page 140

Page: 140 / 623

3-62

Phaser 5500 Printer Service Manual

Jam at Tray n (Feed Out Sensor #3) Troubleshooting Reference

Applicable Parts

References

■

Feed Roller

■

Retard Roller

■

Nudger Roller

■

Feed Out Sensor #3

■

Engine Logic Board

■

Tray 4-5 PWB

■

Tray 4 Feed Out Sensor

■

Tray 5 Feed Out Sensor

■

Print Engine P/J Engine Logic Board (page 10-13)

■

Print Engine Tray 2 & 3 Wiring (page 10-26)

■

PL2.3 Feeder (2/2) (page 9-12)

■

PL8.1 Print Engine Electrical (page 9-40)

■

Phaser 5500 Printer Options Service Manual

■

1000-Sheet Feeder P/J Locator (page 5-5)

■

1000-Sheet Tray 4 & 5 Wiring (page 5-9)

■

PL20.4 Tray 4-5 Feeder (2/2) (page 4-10)

■

PL20.6 Tray 4-5 Drive and Electrical (page 4-16)

Jam at Tray n (Feed Out Sensor #3) Troubleshooting Procedure

Step

Actions and Questions

Yes

Check the paper condition.
Is the paper in the tray damaged?

Replace the
paper.

Go to Step 2.

Check the paper size settings.
Does the paper size match the setting?

Go to Step 3.

Correct paper
size settings.

Remove the tray and check the rollers.
Is the Feed, Retard, or Nudger Roller
worn or contaminated with paper dust?

Clean or replace
the Rollers.

Go to Step 4.

Check the paper position at Door B or C.
Does the paper block the Feed Out
Sensor?

Remove the
paper. If the error
persists, go to
Step 5 for Tray 2
or 3, or Step 9 for
Tray 4 or 5.

Go to Step 5 for
Tray 2 or 3, or
Step 9 for Tray 4
or 5.

Test Feed Out Sensor #3.

1. Open Door B.

2. Run the Service Diagnostics Tray 3

Feed Out Sensor test.

Does the sensor change state?

Go to Step 9.

Go to Step 6.

Check the Feed Out Sensor #3 connection.
Are P/J105, P/J608 and P/J410
connected?

Go to Step 7.

Connect the
sensor.

Check continuity between the Feed Out
Sensor #3 and Engine Logic Board.
Is there continuity on each wire
between P/J105 <=> P/J410?

Go to Step 8.

Repair the wiring.

Check for +5 V at the Feed Out Sensor #3.
Is there +5 V across the sensor
connector’s Pin 1 <=> ground?

Replace Feed Out
Sensor #3.

Replace the
Engine Logic
Board
(page 8-89).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands