Fuji Xerox Phaser 5500 Service Manual Download Page 435

Page: 435 / 623

FRU Disassembly

8-25

Remove the Tray 2 Feeder (page 8-20) or Tray 3 Feeder (page 8-21).

PL2.3.14

Release the hooks securing the Sensor to the Upper Frame as shown in the figure.

Disconnect the connector from the No Paper Sensor.

Remove the No Paper Sensor.

Tray 2 and 3 Level Sensor Actuator

Remove the Tray 1/MPT Rear Cover (page 8-16).

Remove the Tray 1/MPT Feeder (page 8-32).

Remove Door A (page 8-46).

Remove the Take Away Bracket (page 8-40).

No Paper Sensor

Upper Frame

Harness

Feeder

s5500-109

Hooks

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands