manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 66

2-26

Phaser 5500 Printer Service Manual

Major Assemblies and Functions

Components of the Phaser 5500 printer described in this section include:

■

Trays

■

Exit 1 Assembly

■

Printer Drive and Electrical

Trays

Standard trays include the 100-sheet, multi-purpose Tray 1/MPT and two 500-sheet 
universal trays, Trays 2 and 3. The trays adjust to accept various paper sizes. 

Tray 1/MPT

The Tray 1/MPT Feeder feeds paper into the printer. The printer’s Main Motor drives 
the Tray 1/MPT Feed Roller to feed paper from the tray. Tray 1/MPT components 
include:

■

Feed Roller that feeds paper from Tray 1/MPT.

■

Drive Roller that feeds paper into the printer. 

■

Pick-up Solenoid that engages the Main Motor to the Feed Roller.

■

No Paper Sensor that detects whether paper is in Tray 1/MPT.

■

Paper Size Sensor detects the position of the Side Guides and reports the width of 
paper in Tray 1.

Tray 1/MPT incorporates a single set of guides to establish paper width. The time 
required for the paper to clear the No Paper Sensor identifies the paper’s length. When 
media is placed in Tray 1/MPT, the leading edge strikes the actuator of the No Paper 
Sensor indicating the presence of paper. As the last sheet of paper is fed from the tray 
the actuator drops through an opening indicating No Paper remains in the tray.

s5500-035

No Paper Sensor

Paper Size Sensor

Drive Roller

Feed Roller

 Pick Up Solenoid

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands