manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 253

Error Messages, Codes, and Procedures

3-175

Punch Failure (Punch Move Home Sensor) Troubleshooting Reference

Applicable Parts

References

■

Punch Unit Move 
Home Sensor

■

Punch Sensor 
Harness

■

Finisher Main PWB

■

Punch Motor Bracket

■

Punch Drive Harness

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Punch P/J Locator (page 5-31)

■

Finisher Punch (1/2) Wiring (page 5-46)

■

PL25.7 Finisher Punch (page 4-56)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Punch Failure (Punch Move Home Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Check the Punch Unit operation.
Slide the Punch Unit in and out.
Does the Punch Unit move smoothly?

Go to Step 2.

Correct the 
installation.

2

Test the Punch Unit Move Home Sensor.
Run the Service Diagnostics Punch Unit 
Move Home Sensor test.
Does the sensor state when the sensor 
is blocked?

Go to Step 8.

Go to Step 3.

3

Check Punch Unit Move Home Sensor 
Harness connection.
Are P/J8352 and P/J8307 connected?

Go to Step 5.

Connect and go 
to Step 4.

4

Print a Test Print.
Does the error still occur?

Go to Step 5.

Problem solved.

5

Check Punch Unit Move Home Sensor 
Harness continuity.

1. Disconnect P/J8352 and P/J8307.

2. Check for continuity at the following:

P/J8352-3 <=> P/J8307-A6
P/J8352-2 <=> P/J8307-A5
P/J8352-1 <=> P/J8307-A4

Are these conductive?

Go to Step 6.

Repair the Punch 
Unit Move Home 
Sensor Harness.

6

Check for +5 V to the Punch Unit Move 
Home Sensor.
Is there +5 V across J8307-A4 <=> 
J8307-A6 on the Finisher Main PWB?

Go to Step 7.

Replace the 
Finisher Main 
PWB 
(page 3-248).

7

Check the Punch Home Sensor signal.
Does the voltage across P8307-A5 <=> 
P8307-A6 on the Finisher Main PWB 
change when the sensor is blocked?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Replace the 
Punch Unit Move 
Home Sensor 
(page 3-153).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands