Fuji Xerox Phaser 5500 Service Manual Download Page 219

Page: 219 / 623

Error Messages, Codes, and Procedures

3-141

Tray n Failure - H1 -1/2/3/4 Tray n Fail

Detected lift failure. Paper size detection inoperative.

Applicable Error Codes

Tray 2 Failure - H1-1 Tray 2 Fail

Tray 3 Failure - H1-2 Tray 3 Fail

Tray 4 Failure - H1-3 Tray 4 Fail

Tray 5 Failure - H1-4 Tray 5 Fail

Universal Tray Failure Troubleshooting Reference

Applicable Parts

References

■

Tray

■

Feeder

■

Feed/Lift Motor

■

Level Sensor

■

Paper Size Switch

■

Tray 4-5 PWB

■

Engine Logic
Board.

■

Print Engine P/J Tray 2 & 3 Feeders (page 10-11)

■

Print Engine P/J Engine Logic Board (page 10-13)

■

Print Engine Tray 2 & 3 Wiring (page 10-26)

■

PL2.1 Tray (1/2) and Feeder (1/2) (page 9-8)

■

PL2.2 Tray (2/2) (page 9-10)

■

PL2.3 Feeder (2/2) (page 9-12)

■

PL8.1 Print Engine Electrical (page 9-40)

■

Phaser 5500 Printer Options Service Manual

■

1000-Sheet Feeder P/J Locator (page 5-5)

■

1000-Sheet Feeder Tray 4 & 5 Wiring (page 5-9)

■

PL20.2 Tray 4-5 Tray (1/2) Feeder (1/2) (page 4-6)

■

PL20.3 Tray 4-5 Tray (2/2) (page 4-8)

■

PL20.4 Tray 4-5 Feeder (2/2) (page 4-10)

■

PL20.6 Tray 4-5 Drive and Electrical (page 4-16)

Universal Tray Failure Troubleshooting Procedure

Step

Actions and Questions

Yes

Check paper supply.
Is paper loaded in the affected tray?

Go to Step 2.

Load paper and
go to Step 2.

Check the tray.
Replace the tray with one from another
position.
Does the replaced tray lift?

Go to Step 3.

Go to Step 4.

Check lift components.
Is the Sector Gear or surrounding parts
damaged?

Replace the tray.

Go to Step 4.

Test the Feed/Lift Motor.
Run the Service Diagnostics Lift Motor test
for the affected tray.
Does the motor operate properly?

Go to Step 9.

Go to Step 5.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands