manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 311

Error Messages, Codes, and Procedures

3-233

Punch Waste Box is Full

The Punch Box counter has reached its maximum count.

5

Check Punch Sensor Harness continuity.

1. Disconnect P/J8355 and P/J8307.

2. Check for continuity at the following:

J8355-3 <=> J8307-A3
J8355-2 <=> J8307-A2
J8355-1 <=> J8307-A1

Are these conductive?

Go to Step 6.

Repair the Punch 
Sensor Harness.

6

Check for +5 V to the Punch Box Set 
Sensor
Is there +5 V across J8307-A1 <=> 
J8307-A3 on the Finisher Main PWB?

Go to Step 7.

Replace the 
Finisher Main 
PWB 
(page 3-248).

7

Check the Punch Box Set Sensor signal.
Does the voltage across P/J8307-A2 <=> 
P/J8307-A3 on the Finisher Main PWB 
change when the Punch Box is removed 
or replaced?

Go to Step 8.

Replace the 
Punch Box Set 
Sensor 
(page 3-154).

8

Replace the Finisher Main PWB.
Does the error still occur?

Replace the 
Engine Logic 
Board 
(page 8-89).

Problem solved.

Punch Box Full (Punch Box Counter) Troubleshooting Reference

Applicable Parts

References

■

Punch Box Set Sensor

■

Punch Box Sensor 
Harness

■

Punch Sensor 
Harness

■

Finisher Main PWB

■

Engine Logic Board.

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Punch P/J Locator (page 5-31)

■

Finisher Punch (1/2) Wiring (page 5-46)

■

PL8.1 Print Engine Electrical (page 9-40)

■

PL25.7 Finisher Punch (page 4-56)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Punch Box Missing (Punch Box Set Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands