Fuji Xerox Phaser 5500 Service Manual Download Page 199

Page: 199 / 623

Error Messages, Codes, and Procedures

3-121

Jam at H - F4-66 Compile Paper SNR Static

Paper is detected by the Compile Tray No Paper Sensor following an eject operation.

Applicable Error Codes

Jam at H - F4-66 Compile Paper SNR Static

Check the No Paper Sensor signal.
Does the voltage across P8309-2 <=>
P8309-1 on the Finisher Main PWB
change when the actuator is moved?

Replace the
Finisher Main
PWB
(page 3-248).

Replace the
Compile Tray No
Paper Sensor
(page 3-182).

Static Jam at H (No Paper Sensor) Troubleshooting Reference

Applicable Parts

References

■

Eject Clamp Motor

■

Main Drive Harness

■

Eject Motor

■

Finisher Main PWB

■

No Paper Sensor

■

Compiler Harness

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Motors Wiring (page 5-42)

■

Finisher Clutch and Solenoids (page 5-43)

■

Finisher Compiler Tray Wiring (page 5-44)

■

PL25.9 Finisher Eject (1/3) (page 4-60)

■

PL25.10 Finisher Eject (2/3) (page 4-62)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Static Jam at H (No Paper Sensor) Troubleshooting Procedure

Step

Actions and Questions

Yes

Test the Eject Clamp Motor.
Run the Service Diagnostics Eject Clamp
Motor Up and Down tests.
Does the motor rotate properly?

Go to Step 6.

Go to Step 2.

Check Eject Clamp Motor Main Drive
Harness connections.
Are P/J8339 and P/J8304 connected?

Go to Step 4.

Connect and go
to Step 3.

Print a Test Print.
Does the error still occur?

Go to Step 4.

Problem solved.

Jam at H (Compile Tray No Paper Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands