Fuji Xerox Phaser 5500 Service Manual Download Page 489

Page: 489 / 623

FRU Disassembly

8-79

Remove the Main Drive Belt (page 8-83).

10.

Disconnect the connector from the Offset Motor.

11.

Disconnect the two connectors from the two sensors.

12.

Remove the two screws securing the Exit Transport Assembly to the frame.

13.

Remove the Exit Transport Assembly by lifting upward.

s5500-168

Exit Transport
Assembly

Harness
Connectors

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands