manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 340

4-10

Phaser 5500 Printer Service Manual

Print Engine Troubleshooting

Inoperative Printer

No response from printer when the main power is switched on.

Initial Actions

Eliminate the possibility that an installed option is the cause of the problem.

1.

Power Printer Off.

2.

Unplug all installed options (Finisher, 1000-Sheet Feeder, 2000-Sheet Feeder, 
Duplex and Exit 2.

3.

Power the printer On. If printer powers up normally, plug in the options one at a 
time until the defective option is isolated. If the printer remains inoperative, use 
the following procedure to locate the problem.

Inoperative Printer Troubleshooting Reference 

Applicable Parts

References

■

Power Cord

■

GFI Breaker

■

AC Accessory Panel

■

Wall Outlet

■

Print Engine Electrical Specifications (page 1-13)

■

AC Accessory Panel Plug/Jack Locator (page 10-15)

■

PL8.1 Print Engine Electrical (page 9-40)

Inoperative Printer Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Check the AC Power Cord.
Is the AC Power Cord plugged into the 
printer and the AC outlet? 
Is the GFI breaker operational?

Go to Step 2.

Plug in the AC 
Power Cord or 
reset the GFI 
Breaker

2

Check the voltage at the AC outlet. 
Is there approximately 110V (or 220V if a 
220V model) at the AC outlet?

Go to Step 3.

Notify customer 
that the power is 
out of 
specification.

3

Check the AC input Voltage to the LVPS

1. Remove the Upper Right Cover.

2. Power the Printer on.

3. Measure AC voltage at the following test 

points on the LVPS.

T 11 –1 <=>T 12 –1 + 120V or 220 V

Are the voltages within specification?

Go to Step 4.

Go to Step 5.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands