Fuji Xerox Phaser 5500 Service Manual Download Page 144

Page: 144 / 623

3-66

Phaser 5500 Printer Service Manual

Jam at Tray 5 (Feed Out Sensor #5) Troubleshooting Reference

Applicable Parts

References

■

Feed Roller

■

Retard Roller

■

Nudger Roller

■

Engine Logic Board

■

Tray 4-5 PWB

■

Tray 5 Pre-Feed
Sensor

■

Feed Out Sensor #5

■

Print Engine P/J Engine Logic Board (page 10-13)

■

PL8.1 Print Engine Electrical (page 9-40)

■

Phaser 5500 Printer Options Service Manual

■

1000-Sheet Feeder P/J Locator (page 5-5)

■

1000-Sheet Tray 4 & 5 Wiring (page 5-9)

■

PL20.4 Tray 4-5 Feeder (2/2) (page 4-10)

■

PL20.6 Tray 4-5 Drive and Electrical (page 4-16)

Jam at Tray 5 (Feed Out Sensor #5) Troubleshooting Procedure

Step

Actions and Questions

Yes

Check paper condition.
Is the paper in the tray damaged?

Replace the
paper.

Go to Step 2.

Check paper size settings.
Does the paper size match the setting?

Go to Step 3.

Correct paper
size settings.

Remove the tray and check the rollers.
Is the Feed, Retard, or Nudger Roller
worn or contaminated with paper dust?

Clean or replace
the Rollers.

Go to Step 4.

Check paper position at Door C.
Does the paper touch the Tray 5 Pre-
Feed or Feed Out Sensor #5?

Remove the
paper.

Go to Step 5.

Test the Tray 5 Pre-Feed Sensor.

1. Open Door C.

2. Run the Service Diagnostics Tray 5

Pre-Feed Sensor test.

Does the sensor change state?

Go to Step 12.

Go to Step 6.

Check the Tray 5 Pre-Feed Sensor
connection.
Are P/J103A, P/J661A and P/J549A
connected?

Go to Step 7.

Connect the
sensor.

Check continuity between the Tray 5 Pre-
Feed Sensor and Tray 4-5 PWB.
Is there continuity on each wire
between P/J103A <=> P/J549A?

Go to Step 8.

Repair the wiring.

Check for +5 V at Tray 5 Pre-Feed Sensor
Is there +5 V across the sensor
connector’s Pin 1 <=> ground?

Replace the
sensor.

Go to Step 9

Check connections between the Tray 4-5
PWB and Engine Logic Board.
Are P/J541 and P/J413 connected?

Go to Step 10.

Connect P/J541
and P/J413.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands