Fuji Xerox Phaser 5500 Service Manual Download Page 204

Page: 204 / 623

3-126

Phaser 5500 Printer Service Manual

Jam at F or Stacker Upper Tray - F4-7nTop Tray SNR OFF

Paper does not leave the Stacker Upper Tray Exit Sensor on time.

Applicable Error Codes

Jam at F - F4-72 Top Tray Exit SNR OFF Jam A

Jam at Stacker Upper Tray - F4-75 Top Tray Exit SNR OFF Jam B

Check Main Sensor Harness continuity.

1. Disconnect P/J8312 from the harness,

and P/J8302A on the Finisher Main
PWB.

2. Check for continuity at the following:

J8312A-3 <=> P/J8302A-7
J8312A-2 <=> P/J8302A-8
J8312A-1 <=> P/J8302A-9

Are these conductive?

Go to Step 16.

Repair the Main
Sensor Harness.

Check for +5 V to the Upper Tray Exit
Sensor.
Is there +5 V across J8302A-9 <=>
J8302A-7 on the Finisher Main PWB?

Go to Step 48.

Replace the
Finisher Main
PWB
(page 3-248).

Check the Upper Tray Exit Sensor signal.
Does the voltage across P8302A-8 <=>
P8302A-7 on the Finisher Main PWB
change when sensor is actuated?

Replace the
Finisher Main
PWB
(page 3-248).

Replace the
Upper Tray Exit
Sensor
(page 3-226).

Jam at F or Upper Tray (Exit Sensor OFF) Troubleshooting Reference

Applicable Parts

References

■

Transport Roller

■

Pinch Roller

■

Transport Motor

■

Main Drive Harness

■

Finisher Main PWB

■

Top Exit Sensor Harness

■

Main Sensor Harness

■

Top Exit Sensor

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Sensors (1/2) Wiring (page 5-40)

■

Finisher Motors Wiring (page 5-42)

■

PL25.12 Finisher Transport (1/2) (page 4-66)

■

PL25.13 Finisher Transport (2/2) (page 4-68

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Jam at F or G (Stacker Upper Tray Exit Sensor ON) Troubleshooting Procedure

Step

Actions and Questions

Yes

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands