manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 176

3-98

Phaser 5500 Printer Service Manual

Jam at F - F4-36 X’port Ent. SNR Static

Remaining paper is detected in the Finisher Transport Entrance Sensor.

Applicable Error Code

Jam at F - F4-36 X’port Ent. SNR Static

17

Check the harness connections.
Are P/J8319 and P/J8303 of the X’port 
Entrance Sensor, and P/J8302A on the 
Main SNR harness connected?

Go to Step 19.

Reconnect and 
go to Step 18.

18

Print a Test Print.
Does the error still occur?

Go to Step 19.

Problem solved.

19

Check the sensor harness continuity.

1. Disconnect P/J8319 and P/J8303B on 

the X’port Entrance Sensor Harness.

2. Check for continuity at the following:

J8319-3 <=> J8303B-1
J8319-2 <=> J8303B-2
J8319-1 <=> J8303B-3

Are these conductive?

Go to Step 20.

Repair the X’port 
Entrance Sensor 
Harness.

20

Check Main Sensor Harness continuity.
Disconnect P/J8303 on the Main Sensor 
Harness, and P/J8302A on the Finisher 
Main PWB.
Check for continuity at the following:

J8303A-3 <=> J8302A-1
J8303A-2 <=> J8302A-2
J8303A-1 <=> J8302A-3

Are these conductive?

Go to Step 21.

Repair the Main 
Sensor Harness.

21

Check for +5 V to the X’port Entrance 
Sensor
Is there +5 V across J8302A-3 <=> 
J8302A-1 on the Finisher Main PWB?

Go to Step 22.

Replace the 
Finisher Main 
PWB 
(page 3-248).

22

Check the X’port Entrance Sensor signal.
Does the voltage across P8302A-2 <=> 
P8302A-1 on the Finisher Main PWB 
change when the sensor is blocked?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Replace X’port 
Entrance Sensor 
(page 3-117).

Jam at F (Transport Entrance Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands