manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 248

3-170

Phaser 5500 Printer Service Manual

Stacker Lower Tray Failure - H5-2n Rear Home SNR

For H-22, the Rear Tamper Home Sensor is not turned On within 800 ms following 
the Rear Tamper beginning to move to the Rear Tamper Home position. For H5-24, 
the Rear Tamper Home Sensor is not turned Off in the time specified following the 
Rear Tamper leaving the home position, or the Rear Tamper Home Sensor is turned 
On again after the Rear Tamper Home Sensor is turned Off and the Rear Tamper stops 
moving.

Applicable Error Codes

Stacker Lower Tray Failure - H5-22 Rear Home SNR ON

Stacker Lower Tray Failure - H5-24 Rear Home SNR OFF

11

Check Compiler Front Tamper Motor 
Harness continuity.

1. Disconnect P/J8363B and P/J8309.

2. Check for continuity at the following:

P/J8363B-6 <=> P/J8309-10
P/J8363B-5 <=> P/J8309-11
P/J8363B-4 <=> P/J8309-12
P/J8363B-3 <=> P/J8309-13
P/J8363B-2 <=> No connection
P/J8363B-1 <=> P/J8309-14

Are these conductive?

Go to Step 12.

Repair the 
Compiler Front 
Tamper Motor 
Harness.

12

Check for +24 V to the Front Tamper Motor.
Is there +24 V across J8309-11 <=> 
ground on the Finisher Main PWB?

Go to Step 13.

Replace the 
Finisher Main 
PWB 
(page 3-248).

13

Replace the Front Tamper Motor.
Print a Test Print.
Does the error still occur?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Problem solved.

Tamper (Rear Tamper Home Sensor) Troubleshooting Reference

Applicable Parts

References

■

Rear Tamper Home 
Sensor

■

Compiler Tray Assembly

■

Compiler Harness

■

Finisher Main PWB

■

Rear Tamper Motor

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Compiler P/J Locator (page 5-33)

■

Finisher Compiler Tray Wiring (page 5-44)

■

PL25.10 Finisher Eject (2/3) (page 4-62)

■

PL25.14 Finisher Electrical (page 4-70)

Tamper (Front Tamper Home Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands