manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 246

3-168

Phaser 5500 Printer Service Manual

Stacker Lower Tray Failure - H5-2n Front Home SNR

For H5-21, the Front Tamper Home Sensor is not turned On within 800 ms following 
the Front Tamper beginning to move to the Front Tamper Home position. For H5-23, 
the Front Tamper Home Sensor is not turned Off in the time specified following the 
Front Tamper leaving the home position, or the Front Tamper Home Sensor is turned 
On again after the Front Tamper Home Sensor is turned Off and the Front Tamper 
stops moving.

Applicable Error Codes

Stacker Lower Tray Failure - H5-21 Front Home SNR ON

Stacker Lower Tray Failure - H5-23 Front Home SNR OFF

22

Print a Test Print.
Does the error still occur?

Go to Step 23.

Problem solved.

23

Replace the Elevator Motor.
Print a Test Print.
Does the error still occur?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Problem solved.

Tamper (Front Tamper Home Sensor) Troubleshooting Reference

Applicable Parts

References

■

Front Tamper Home 
Sensor

■

Compiler Tray Assembly

■

Compiler Harness

■

Finisher Main PWB

■

Front Tamper Motor

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Compiler P/J Locator (page 5-33)

■

Finisher Compiler Tray Wiring (page 5-44)

■

PL25.10 Finisher Eject (2/3) (page 4-62)

■

PL25.14 Finisher Electrical (page 4-70)

Tamper (Front Tamper Home Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Check the Tamper mechanism.
Move the Front Tamper mechanism.
Does the Tamper mechanism operate 
smoothly?

Go to Step 2.

Repair or replace 
the Compiler Tray 
(page 3-177).

Stacker Lower Trail Failure (Stacker Encoder Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands