manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 310

3-232

Phaser 5500 Printer Service Manual

Punch Waste Box is Missing

The Punch Box Set Sensor indicates the Punch Box is not installed in the Finisher. 

Punch Box Missing (Punch Box Set Sensor) Troubleshooting Reference

Applicable Parts

References

■

Punch Box Set Sensor

■

Punch Box Sensor 
Harness

■

Punch Sensor 
Harness

■

Finisher Main PWB

■

Engine Logic Board.

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Punch P/J Locator (page 5-31)

■

Finisher Punch (1/2) Wiring (page 5-46)

■

PL8.1 Print Engine Electrical (page 9-40)

■

PL25.7 Finisher Punch (page 4-56)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Punch Box Missing (Punch Box Set Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Test the Punch Box Set Sensor.

1. Open Door G.

2. Remove the Punch Box.

3. Run the Service Diagnostics Punch Box 

Set Sensor test.

Does the sensor state change when the 
Punch Box is removed and replaced?

Go to Step 8.

Go to Step 2.

2

Check the harness connections.
Are P/J8353 and P/J8355 of the Punch 
Box Sensor Harness, and  P/J8355 and 
P/J8307 of the Punch Sensor Harness 
connected?

Go to Step 4.

Connect and go 
to Step 3.

3

Cycle the printer power.
Does the error still occur?

Go to Step 4.

Problem solved.

4

Check Punch Box Sensor Harness 
continuity.

1. Disconnect P/J8353 and P/J8355.

2. Check for continuity at the following:

J8353-3 <=> P8355-3
J8353-2 <=> P8355-2
J8353-1 <=> P8355-1

Are these conductive?

Go to Step 5.

Repair the wiring.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands