manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 262

3-184

Phaser 5500 Printer Service Manual

Stapler Failure - H5-91 Staple Fail

The Stapler Home Sensor state is not detected within the specified time after a Stapler 
Move Motor forward operation, or the Stapler Home Sensor is not turned ON within 
the specified time following a Stapler Move Motor reverse operation.

Applicable Error Code

Stapling Failure - H5-91 Staple Fail

Stapler Failure (Stapler Home Sensor) Troubleshooting Reference

Applicable Parts

References

■

Stapler Assembly

■

Staple Home Position 
Sensor

■

Staple Motor

■

Stapler Harness

■

Finisher Main PWB

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Staple P/J Locator (page 5-30)

■

Finisher Stapler Wiring (page 5-45)

■

PL8.1 Print Engine Electrical (page 9-40)

■

PL25.8 Finisher Staple (page 4-58)

■

PL25.14 Finisher Electrical (page 4-70)

Stapler Failure (Stapler Home Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Test the Stapler Assembly.
Run the Service Diagnostics Staple Motor 
Forward and Reverse tests.
Does the Stapler Motor rotate normally?

Go to Step 5.

Go to Step 2.

2

Check the Staple Motor Harness 
connections.
Are P/J8357 and P/J8308 connected?

Go to Step 4.

Connect and go 
to Step 3.

3

Print a Test Print.
Does the error still occur?

Go to Step 4.

Problem solved.

4

Check the Staple Motor Harness continuity

1. Disconnect P/J8357 and P/J8308.

2. Check for continuity at the following:

P/J8357-1 <=> P/J8308-10
P/J8357-2 <=> P/J8308-9
P/J8357-3 <=> P/J8308-8
P/J8357-4 <=> P/J8308-7

Are these conductive?

Go to Step 9.

Repair the Staple 
Motor Harness.

5

Test the Staple Head Home Sensor.
Run the Service Diagnostics Staple Head 
Home Sensor test.
Does the sensor state change when the 
staple gear is rotated?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Go to Step 6.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands