manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 148

3-70

Phaser 5500 Printer Service Manual

14

Check the Main Harness for continuity.

1. Disconnect PF56 and JF06.

2. Check for continuity at the following:

PF56-1 <=> JF06-1
PF56-2 <=> JF06-3
PF56-3 <=> JF06-2
PF56-4 <=> JF06-6
PF56-5 <=> JF06-4
PF56-6 <=> JF06-5

Are these conductive?

Go to Step 15.

Repair the Main 
Harness.

15

Check resistance of the Feed/Lift Motor.
Is there some amount of resistance 
across PF58-2/5(COM) and PF58-1/3/4/
6?

Go to Step 16.

Replace the 
Feed/Lift Motor 
(page 3-49).

16

Check for +24 V at the Feed/Lift Motor.
Is there +24 V across PF06-3 <=> PF04-3 
and PF06-4 <=> PF04-3 on the PWB?

Go to Step 17.

Replace the Tray 
6 PWB 
(page 3-67).

17

Replace the Feed/Lift Motor.
Print a Test Print.
Does the error still occur?

Go to Step 27.

Problem solved.

18

Test the Nudger Solenoid.
Run the Service Diagnostics Tray 6 Nudger 
Solenoid Test at High Power.
Does the Nudger Solenoid activate?

Go to Step 27.

Go to Step 19.

19

Check the harness connections.
Are the connectors PF59, PF56A, and 

 

P/JF06 on the PWB connected?

Go to Step 21.

Connect and go 
to Step 20.

20

Print a Test Print.
Does the error still occur?

Go to Step 21.

Problem solved.

21

Check the Feeder Harness for continuity

1. Disconnect PF59 and JF56A.

2. Check for continuity at the following:

PF59-2 <=> JF56A-1
PF59-1 <=> JF56A-2

Are these conductive?

Go to Step 22.

Repair the Feeder 
Harness.

22

Check the Main Harness for continuity

1. Disconnect PF56A and JF06.

2. Check for continuity at the following:

PF56A-6 <=> JF06-13
PF56A-5 <=> JF06-14

Are these conductive?

Go to Step 23.

Repair the Main 
Harness.

23

Check Nudger Solenoid resistance. 
Is there some amount of resistance 
across PF59-1 and PF59-2?

Go to Step 24.

Replace the 
Nudger Solenoid 
(page 3-50).

Jam at Tray 6 (Feed Out Sensor #6) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands