Fuji Xerox Phaser 5500 Service Manual Download Page 110

Page: 110 / 623

3-32

Phaser 5500 Printer Service Manual

Fan Failure - U4-9 Fan Defect

The Fuser Fan failed.

Applicable Error Codes

Fuser Failure - U4-9 Fan Defect

Fuser Fan Failure Troubleshooting Reference

Applicable Parts

References

■

Fuser Fan

■

Motor Assembly

■

Engine Logic Board

■

Print Engine P/J Electrical (page 10-12)

■

Print Engine Drive/CRUM Wiring (page 10-25)

■

PL5.1 Laser, CRU and Toner Dispense (page 9-32)

■

PL7.1 Print Engine Drive (page 9-38)

■

PL8.1 Print Engine Electrical (page 9-40)

Fuser Fan Failure Troubleshooting Procedure

Step

Actions and Questions

Yes

Check the Fuser Fan installation.

1. Remove the I/P Board Cover.

2. Remove the Upper Rear Cover.

Is the Fan installed properly (label out)?

Go to Step 2.

Correct the
installation.

Check if the Fuser Fan rotates.
Does the Fan rotate?

Go to Step 7.

Go to Step 3.

Test the Fuser Fan.
Run the Service Diagnostic Fuser Fan test.
Does the Fuser Fan operate properly?

Go to Step 7.

Go to Step 4.

Check the Fuser Fan connection (CN102).
Is the Fan connected?

Go to Step 5.

Connect the Fan.

Check continuity between the Fan and
Motor Assembly (CN102).
Is there continuity on each wire?

Go to Step 6.

Replace the Fan
(page 8-59).

Check for +24 V to the Fuser Fan.
Is there +24 V across CN102-3(+) <=>
ground?

Replace the Fan
(page 8-59).

Replace the
Engine Logic
Board
(page 8-89), then
replace the Motor
Assembly.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands