manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 301

Error Messages, Codes, and Procedures

3-223

Stacker Lower Tray Full - Finisher Mix Full Stack

The Stacker Encoder Sensor for the Stacker Lower Tray indicates a Stack Full 
condition.

6

Check for +5 V to the Top Tray Full Sensor.
Is there +5 V across J8302A-12 <=> 
J8302A-10 on the Finisher Main PWB?

Go to Step 7.

Replace the 
Finisher Main 
PWB 
(page 3-248).

7

Check the Top Tray Full Sensor signal.
Does the voltage across P8302A-11 <=> 
P8302A-10 on the Finisher Main PWB 
change when the sensor is covered?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Replace the 
Upper Tray Full 
sensor 
(page 3-233).

Lower Tray Full (Stack Encoder Sensor) Troubleshooting Reference

Applicable Parts

References

■

Finisher Main 
PWB

■

Main Sensor 
Harness

■

Stacker Encoder 
Sensor

■

Elevator Motor

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Sensors (2/2) Wiring (page 5-41)

■

Finisher Clutch and Solenoids Wiring (page 5-43)

■

PL25.6 Finisher Stack (page 4-54)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Lower Tray Full (Stack Encoder Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Check the Stacker Lower Tray for 
obstructions.
Are there any obstacles in the path of 
the Stacker Lower Tray?

Remove the 
obstacles.

Go to Step 2.

2

Check the Encoder wheel installation.
Does the Encoder rotate and enter the 
sensing area of the Stacker Encode 
Sensor?

Go to Step 3.

Correct and go to 
Step 3.

3

Test the Stacker Encoder Sensor.
Run the Service Diagnostics Stacker 
Encode Sensor test.
Does the sensor state change when the 
Elevator Motor Belt is moved by hand 
rotating the Encoder Wheel?

Go to Step 9.

Go to Step 4.

Upper Tray Full (Upper Tray Full Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands