manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 85

Error Messages, Codes, and Procedures

3-7

Service Usage Profile

The Service Usage Profile tracks printer activity, consumable usage and printer 
history. This data is stored in NVRAM. Service Usage Profile data includes error logs 
that retain detail on the type, date, location and frequency of engine and jam errors. 
While the Service Usage Profile includes data on all aspects of the printer, this section 
focuses on accessing these two error logs to review printer history.

Accessing Fault Histories

Access Service Usage Profile fault histories by:

Print (if possible) the Service Usage Profile. 

a.

At the printer’s Front Panel, go to the 

Troubleshooting

 menu

 

and select 

Service Tools

. 

b.

From the 

Service Tools

 menu, select 

Service Usage Profile. 

The 

engine and jam error fault histories are detailed at lines 262 and 298 
respectively. 

Or...

View fault history logs on the Front Panel.

a.

At the printer’s Front Panel, go to the 

Troubleshooting 

menu

 

and select

 

Service Tools

.

b.

From the 

Service Tools

 menu, select 

Engine Error 

or

 Jam History

.

Or...

If the printer is operational and connected to a network, view the fault history 
using a browser.

a.

Open a web browser.

b.

Enter the printer’s IP address as the URL.

c.

Select the 

Troubleshoot

 link and the 

Fault History

 displays.

Interpreting Fault History Error Codes

Fault histories appear on the Front Panel as a list of semi-colon separated codes. A 
partial example of the Engine Error Log as it appears on the display:

0,0; 0,0; 0,0; 0,0;13, <pg_count>;13, <pg_count>;13,<pg_count>;...

The fault history logs for the engine and jams each contain 30 entries. Log entries 
move right to left. Each successive error shifts the log left, with the oldest code falling 
off the left and the latest code added to the right. Note that a value of 0 (zero) or “--“ 
in a log indicates no data and <pg_count> indicates the value of the Total Page 
counter at the point when the error occurred. For display, the Engine Error Log 
combines the error code and page count (lines 262 and 263 of the printed Service 
Usage Profile).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands