manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 177

Error Messages, Codes, and Procedures

3-99

Static Jam at F (Transport Entrance Sensor) Troubleshooting Reference

Applicable Parts

References

■

X’port Entrance Sensor

■

Harness Main SNR

■

Harness Ent. Sensor

■

Harness Main Drive

■

Finisher Main PWB

■

Transport Motor

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Sensors (1/2) Wiring (page 5-40)

■

Finisher Motors Wiring (page 5-42)

■

PL25.12 Finisher Transport (1/2) (page 4-66)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Static Jam at F (Transport Entrance Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Test the H-’Xport Entrance Sensor.

1. Open Door F.

2. Run the Service Diagnostic H-’Xport 

Entrance Sensor test.

Does the sensor change state?

Go to Step 8.

Go to Step 2.

2

Check the Sensor Harness connections.
Is the harness connected to the sensor 
and Finisher correctly?

Go to Step 4.

Connect and go 
to Step 3.

3

Print a Test Print.
Does the error still occur?

Go to Step 4.

Problem solved.

4

Check Sensor Harness continuity.

1. Disconnect P/J8319 and P/J8303B.

2. Check for continuity at the following:

J8319-3 <=> J8303B-1
J8319-2 <=> J8303B-2
J8319-1 <=> J8303B-3

Are these conductive?

Go to Step 5.

Repair the 
Sensor Harness.

5

Check Main Sensor Harness continuity.

1. Disconnect P/J8303A on the harness, 

and P/J8302A on the Finisher Main 
PWB.

2. Check for continuity at the following:

J8303A-3 <=> J8302A-1
J8303A-2 <=> J8302A-2
J8303A-1 <=> J8302A-3

Are these conductive?

Go to Step 6.

Repair the Main 
Sensor Harness.

6

Check for +5 V to the Entrance Sensor.
Is there +5 V across J8302A-3 <=> 
J8302A-1 on the Finisher Main PWB?

Go to Step 7.

Replace the 
Finisher Main 
PWB 
(page 3-248).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands