Fuji Xerox Phaser 5500 Service Manual Download Page 255

Page: 255 / 623

Error Messages, Codes, and Procedures

3-177

Eject Clamp Failure (Eject Clamp Home Sensor) Troubleshooting Reference

Applicable Parts

References

■

Eject Clamp Home
Sensor

■

Eject Clamp Sensor
Harness

■

Finisher Main PWB

■

Eject Clamp Motor

■

Eject Clamp Motor
Harness

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Input Drive P/J Locator (page 5-32)

■

Finisher Sensors (2/2) Wiring (page 5-41)

■

Finisher Clutch and Solenoids Wiring (page 5-43)

■

PL25.9 Finisher Eject (1/3) (page 4-60)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Eject Clamp Failure (Eject Clamp Home Sensor) Troubleshooting Procedure

Step

Actions and Questions

Yes

Check the Eject Clamp operation.
Rotate the Eject Clamp Motor.
Does the Eject Clamp move smoothly?

Go to Step 2.

Correct the
installation.

Test the Eject Clamp Home Sensor.
Run the Service Diagnostics Eject Clamp
Home Sensor test.
Does the sensor change state?

Go to Step 8.

Go to Step 3.

Check Eject Clamp Sensor Harness
connection.
Are P/J8324 and P/J8302B connected?

Go to Step 5.

Connect and go
to Step 4.

Print a Test Print.
Does the error still occur?

Go to Step 5.

Problem solved.

Check Eject Clamp Sensor Harness
continuity.

1. Disconnect P/J8324 and P/J8302B.

2. Check for continuity at the following:

P/J8324-3 <=> P/J8302B-6
P/J8324-2 <=> P/J8302B-7
P/J8324-1 <=> P/J8302B-8

Are these conductive?

Go to Step 6.

Repair the Eject
Clamp Sensor
Harness.

Check for +5 V to the Eject Clamp Home
Sensor.
Is there +5 V across J8302B-8 <=>
J8302B-6 on the Finisher Main PWB?

Go to Step 7.

Replace the
Finisher Main
PWB
(page 3-248).

Check the Eject Clamp Home Sensor
signal.
Does the voltage across P8302B-7 <=>
P8302B-6 on the Finisher Main PWB
change when the sensor is blocked?

Replace the
Finisher Main
PWB
(page 3-248).

Replace the Eject
Clamp Home
Sensor
(page 3-175).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands