manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 306

3-228

Phaser 5500 Printer Service Manual

Stapler Failure - Staple Failure

The status of the Staple Home Sensor is not determined within the time specified 
following a Stapler Move Motor forward operation. For Staple Move Motor reverse, 
the Staple Home Sensor is not turned On in the time specified.

Stapler Failure (Staple Head Home Sensor) Troubleshooting Reference

Applicable Parts

References

■

Finisher Main PWB

■

Staple Harness

■

Stapler Assembly

■

Engine Logic Board.

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Staple P/J Locator (page 5-30)

■

Finisher Stapler Wiring (page 5-45)

■

PL25.8 Finisher Staple (page 4-58)

■

PL25.14 Finisher Electrical (page 4-70)

Stapler Failure (Staple Head Home Sensor) Troubleshooting Procedure 

Step

Actions and Questions

Yes

No

1

Check the Compiler Tray for obstructions.
Are there any obstructions in the 
Compiler Tray?

Remove the 
obstacles.

Go to Step 2.

2

Test the Staple Motor in the Staple Head.
Run the Service Diagnostics Staple Motor 
Forward and Reverse tests alternately.
Does the Staple Motor operate?

Go to Step 6.

Go to Step 3.

3

Check the Staple Motor Harness 
connections.
Are P/J8357 and P/J8308 connected?

Go to Step 5.

Connect and go 
to Step 4.

4

Cycle the printer power.
Does the error still occur?

Go to Step 5.

Problem solved.

5

Check Staple Motor Harness continuity.

1. Disconnect P/J8357 and P/J8308.

2. Check for continuity at the following:

J8357-1 <=> J8308-10
J8357-2 <=> J8308-9
J8357-3 <=> J8308-8
J8357-4 <=> J8308-7

Are these conductive?

Go to Step 11.

Repair the Staple 
Harness.

6

Test the Staple Head Home Sensor.
Run the Service Diagnostics Staple Head 
Home Sensor test.
Does the sensor state change when the 
Staple gear is rotated?

Go to Step 12.

Go to Step 7.

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands