Fuji Xerox Phaser 5500 Service Manual Download Page 436

Page: 436 / 623

8-26

Phaser 5500 Printer Service Manual

Remove the Tray 2 Feeder (page 8-20) or Tray 3 Feeder (page 8-21).

PL2.3.13

Release the two bosses on the Actuator securing the Actuator to the Upper
Frame.

Remove the Actuator.

Note

As an alternate procedure, remove Trays 2 and 3, then reach in and release the
actuator bosses from the feeder assembly.

Feeder

Actuator

Bosses

s5500-108

Upper Frame

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands