Altera Cyclone V Page 849 Device Handbook Download | Manualshive

Page: 849 / 1077

background image

• Control registers— allow you to control the DMAC.
• DMA channel thread status registers—provide the status of the DMA channel threads.
• AXI and loop counter status registers—provide the AXI transfer status and the loop counter status, for

each DMA channel thread.

• Debug registers—enable the following functionality:

• Allow you to send instructions to a thread when debugging the program code.
• Allow system firmware to send instructions to the DMA manager thread.

• Configuration registers—enable system firmware to identify the configuration of the DMAC and control

the behavior of the watchdog.

• Component ID registers— enable system firmware to identify peripherals. Do not attempt to access

reserved or unused address locations. Attempting to access these locations can result in an unpredictable
behavior.

Related Information

Issuing Instructions to the DMAC using a Slave Interface

on page 16-9

Address Map and Register Definitions

The address map and register definitions reside in the hps.html file that accompanies this handbook volume.
Click the link below to open the file.

To view the module description and base address, scroll to and click the following links for the module
instance:

• dmanonsecure
• dmasecure

To view the register and field descriptions, scroll to and click the register names. The register addresses are
offsets relative to the base address of each module instance.

Related Information

•

Introduction to Cyclone V Hard Processor System (HPS)

on page 1-1

The base addresses of all modules are also listed in the

Introduction to the Hard Processor

chapter.

•

The base addresses of all modules are also listed in the

Introduction to the Hard Processor System

chapter

in the

Cyclone V Device Handbook, Volume 3

.

Document Revision History

Table 16-5: Document Revision History

Changes

Version

Date

Maintenance release.

2013.12.30

December 2013

Minor updates.

1.1

November 2012

Initial release.

1.0

January 2012

Altera Corporation

DMA Controller

Send Feedback

16-53

Address Map and Register Definitions

cv_54016
2013.12.30

«
...
847
848
849
850
851
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: B2 Pages: 52

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Brand: Vonets Pages: 8

Brand: IEI Technology Pages: 3

Brand: Taiwan Commate Computer Inc. Pages: 29

Brand: Velopex Pages: 7

SUPERLOADER DLT MAGAZINE

Brand: Tandberg Data Pages: 6

Brand: UNA AUTOMATION Pages: 20

Brand: Tektronix Pages: 178

Elite Controller

Brand: RANA Systems Pages: 328

Brand: PairGain Pages: 80

Brand: Ista Pages: 16

Brand: IFM Pages: 12

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

NC-MCO - TECHNICAL

Brand: Crest Audio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands