Altera Cyclone V Device Handbook Download Page 89 | Manualshive

Page: 89 / 1077

background image

Related Information

Altera Phase-Locked Loop (ALTERA_PLL) Megafunction User Guide

Provides more information about PLL software support in the Quartus II software.

Programmable Phase Shift

The programmable phase shift feature allows the PLLs to generate output clocks with a fixed phase offset.

The VCO frequency of the PLL determines the precision of the phase shift. The minimum phase shift
increment is 1/8 of the VCO period. For example, if a PLL operates with a VCO frequency of 1000 MHz,
phase shift steps of 125 ps are possible.

The Quartus II software automatically adjusts the VCO frequency according to the user-specified phase shift
values entered into the megafunction.

Programmable Duty Cycle

The programmable duty cycle allows PLLs to generate clock outputs with a variable duty cycle. This feature
is supported on the PLL post-scale counters.

The duty-cycle setting is achieved by a low and high time-count setting for the post-scale counters. To
determine the duty cycle choices, the Quartus II software uses the frequency input and the required multiply
or divide rate.

The post-scale counter value determines the precision of the duty cycle. The precision is defined as 50%
divided by the post-scale counter value. For example, if the

C0

counter is 10, steps of 5% are possible for

duty-cycle choices from 5% to 90%. If the PLL is in external feedback mode, set the duty cycle for the counter
driving the

fbin

pin to 50%.

Combining the programmable duty cycle with programmable phase shift allows the generation of precise
non-overlapping clocks.

Clock Switchover

The clock switchover feature allows the PLL to switch between two reference input clocks. Use this feature
for clock redundancy or for a dual-clock domain application where a system turns on the redundant clock
if the previous clock stops running. The design can perform clock switchover automatically when the clock
is no longer toggling or based on a user control signal,

clkswitch

.

The following clock switchover modes are supported in Cyclone V PLLs:

• Automatic switchover—The clock sense circuit monitors the current reference clock. If the current

reference clock stops toggling, the reference clock automatically switches to

inclk0

or

inclk1

clock.

• Manual clock switchover—Clock switchover is controlled using the

clkswitch

signal. When the

clkswitch

signal goes from logic low to logic high, and stays high for at least three clock cycles, the reference clock
to the PLL is switched from

inclk0

to

inclk1

, or vice-versa.

• Automatic switchover with manual override—This mode combines automatic switchover and manual

clock switchover. When the

clkswitch

signal goes high, it overrides the automatic clock switchover

function. As long as the

clkswitch

signal is high, further switchover action is blocked.

Automatic Switchover

Cyclone V PLLs support a fully configurable clock switchover capability.

Clock Networks and PLLs in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52004

Programmable Phase Shift

4-32

2014.01.10

«
...
87
88
89
90
91
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: Jetter Pages: 35

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: Paradyne Pages: 112

Brand: Lorex Pages: 186

Brand: ebm-papst Pages: 11

Brand: YASKAWA Pages: 15

Brand: DAD Pages: 16

Brand: Addonics Technologies Pages: 1

Brand: ICP DAS USA Pages: 8

Super Sound Set SR-JV80-07

Brand: Roland Pages: 8

Brand: Schrack Technik Pages: 2

Brand: Cytron Technologies Pages: 13

PCM-4141 Series

Brand: Advantech Pages: 96

Brand: Hauppauge Pages: 62

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Brand: Idis Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands