manualshive.com logo in svg

Altera Cyclone V, Device Handbook

Share
Download
Altera Cyclone V Device Handbook Download Page 530

Fixed Bursts

The interconnect converts

FIXED

bursts to one or more

INCR1

or

INCRn

bursts depending on the downsize

ratio.

Bypass Merge

If the programmable bit

bypass_merge

is enabled, the interconnect does not perform any packing of

beats to match the optimal

SIZE

for maximum throughput, up to the output data width

SIZE

. Bypass

merge is accessible through the GPV registers and is only accessible to secure masters.

If an exclusive transaction is split into multiple transactions at the output of the downsizing function, the
exclusive flag is removed and the master never receives an

EXOKAY

response. Response priority is the same

as for the upsizing function

Related Information

Upsizing Data Width Function

on page 4-17

Lock Support

Lock is not supported by the interconnect. For atomic accesses, masters can perform exclusive accesses when
sharing data located in the HPS SDRAM.

Related Information

SDRAM Controller Subsystem

on page 8-1

For more information about exclusive access support, refer to the

SDRAM Controller Subsystem

chapter.

FIFO Buffers and Clocks

The interconnect contains FIFO buffers in the majority of the interfaces exposed to the HPS master and
slaves, as well as between the subswitches. These FIFO buffers also provide clock domain crossing for masters
and slaves that operate at a different clock frequency than the switch they connect to.

Data Release Mechanism

For network ports containing write data FIFO buffers with a depth of four or greater, you can set a write
tidemark function,

wr_tidemark

. This tidemark level stalls the release of the transaction until one of the

following situations occurs:

• The interconnect receives the

WLAST

beat of a burst.

• The write data FIFO buffer becomes full.
• The number of occupied slots in the write data FIFO buffer exceeds the write tidemark.

Related Information

Interconnect Master Properties

on page 4-14

This topic contains information about which interfaces contain write data FIFO buffers with a depth of four
or greater.

Resets

The interconnect has one reset signal. The reset manager drives this signal to the SD/MMC controller on a
cold or warm reset. On reset, the boot ROM is mapped to address 0x0. The DAP virtually maps to ID 2.

Altera Corporation

Interconnect

Send Feedback

4-19

Fixed Bursts

cv_54004
2013.12.30

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands