Altera Cyclone V Device Handbook Download Page 1041 | Manualshive

Page: 1041 / 1077

background image

Related Information

•

Memory-Mapped Interfaces

on page 28-2

•

Mentor Verification IP Altera Edition User Guide

Lightweight HPS-to-FPGA AXI Master Interface

The lightweight HPS-to-FPGA AXI master interface,

h2f_lw_axi_master

, is connected to a Mentor

Graphics AXI master BFM for simulation. Qsys configures the BFM as shown in the following table. The
BFM clock input is connected to

h2f_lw_axi_clock

clock.

Table 29-7: Configuration of Lightweight HPS-to-FPGA AXI Master BFM

Value

Parameter

21

AXI Address Width

32

AXI Read and Write Data Width

12

AXI ID Width

You control and monitor the AXI master BFM by using the BFM API.

Related Information

•

Memory-Mapped Interfaces

on page 28-2

•

Mentor Verification IP Altera Edition User Guide

FPGA-to-HPS SDRAM Interface

The HPS component contains a memory interface simulation model to which all of the FPGA-to-HPS
SDRAM interfaces are connected. The model is based on the HPS implementation and provides cycle-level
accuracy, reflecting the true bandwidth and latency of the interface. However, the model does not have the
detailed configuration provided by the HPS software, and hence does not reflect any inter-port scheduling
that might occur under contention on the real hardware when different priorities or weights are used.

Related Information

Functional Description—Hard Memory Interface

For more information, refer to “EMI-Related HPS Features in SoC Devices” in the

Functional

Description—Hard Memory Interface

chapter in volume 3 of the

External Memory Interface Handbook

.

HPS-to-FPGA MPU General Purpose I/O Interface

The HPS-to-FPGA MPU general-purpose I/O interface is connected to an Altera conduit BFM for simulation.
The following table lists the name of each interface, along with API function names for each type of simulation.
You can monitor the interface state changes or set the interface by using the API listed.

Altera Corporation

HPS Simulation Support

Send Feedback

29-5

Lightweight HPS-to-FPGA AXI Master Interface

cv_54030
2013.12.30

«
...
1039
1040
1041
1042
1043
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Univerge SV8100

Brand: NEC Pages: 44

Brand: Paradyne Pages: 12

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: Queclink Pages: 9

NetStructure ZT 5515

Brand: Intel Pages: 90

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: SIIG Pages: 20

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

Brand: Keil Pages: 68

Brand: McIntosh Pages: 44

ENHANCED PSD 239 H2R

Brand: ADTRAN Pages: 2

Brand: Cypress Semiconductor Pages: 9

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: Thecus Pages: 90

Brand: Zhone Pages: 494

Brand: ebm-papst Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands