manualshive.com logo in svg

Altera Cyclone V, Device Handbook

Share
Download
Altera Cyclone V Device Handbook Download Page 1029

Memory-Mapped Interfaces

FPGA-to-HPS Bridge

Table 28-1: FPGA-to-HPS Bridges and Clocks

Associated Clock Interface

(1)

Description

Interface Name

f2h_axi_clock

FPGA-to-HPS AXI slave interface

f2h_axi_slave

The FPGA-to-HPS interface is a configurable data width AXI slave allowing FPGA masters to issue
transactions to the HPS. This interface allows the FPGA fabric to access the majority of the HPS slaves. This
interface also provides a coherent memory interface.

The FPGA-to-HPS interface is an AXI-3 compliant interface with the following features:

• Configurable data width: 32, 64, or 128 bits
• Accelerator Coherency Port (ACP) sideband signals
• HPS-side AXI bridge to manage clock crossing, buffering, and data width conversion.

Other interface standards in the FPGA fabric, such as connecting to Avalon

®

Memory-Mapped (Avalon-

MM) interfaces, can be supported through the use of soft logic adaptors. The Qsys system integration tool
automatically generates adaptor logic to connect AXI to Avalon-MM interfaces.

This interface has an address width of 32 bits. To access existing Avalon-MM/AXI masters, you can use the
Altera

®

Address Span Extender.

Related Information

•

Clocks

on page 28-5

•

Features of the AXI Bridges

For more information, refer to the

HPS FPGA AXI Bridges Component

chapter.

•

HPS Component Interfaces

on page 28-1

For information about the address span extender, refer to “Using the Address Span Extender Component”
in the

Instantiating the HPS Component

chapter.

ACP Sideband Signals

For communication with the ACP on the microprocessor unit (MPU) subsystem, AXI sideband signals are
used to describe the inner cacheable attributes for the transaction.

Related Information

Cortex-A9 MPCore

on page 6-4

For more information about the ACP sideband signals, refer to the

Cortex-A9 MPU Subsystem

chapter.

HPS Component Interfaces

Altera Corporation

Send Feedback

cv_54028

Memory-Mapped Interfaces

28-2

2013.12.30

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands