Altera Cyclone V Device Handbook Download | Manualshive

Page: 384 / 1077

background image

Receiver Datapath

Transmitter Datapath

Data Rates (Gbps)

PCS Support

The same as custom single-
and double-width modes, plus
the RX deterministic latency

The same as custom
single- and double-
width modes, plus the
TX deterministic
latency

0.768, 1.536, 3.072

OBSAI

Implemented using soft PCS

Implemented using
soft PCS

3.125

XAUI

Related Information

•

Use this chapter along with the Altera Transceiver PHY IP Core User Guide.

•

Upcoming Cyclone V Device Features

•

Cyclone V Device Handbook: Known Issues

Lists the planned updates to the

Cyclone V Device Handbook

chapters.

PCI Express

The Cyclone Vdevices have PCIe Hard IP that is designed for performance, ease-of-use, and increased
functionality. The Hard IP consists of the media access control (MAC) lane, data link, and transaction layers.
The PCIe Hard IP supports the PCIe Gen1 end point and root port up to x4 lane configurations. The PCIe
endpoint support includes multifunction support for up to eight functions and Gen2 x4 lane configurations.

Figure 4-1: PCIe Multifunction for Cyclone V Devices

FPGA Device

PCIe Link

Host CPU

Memory

Controller

Root

Complex

Local

Peripheral 1

Local

Peripheral 2

PCIe

RP

PCIe

EP

CAN

GbE

ATA

Bridge

to

PCIe

SPI

GPIO

I

²

C

USB

External System

The Cyclone V PCIe Hard IP operates independently from the core logic, which allows the PCIe link to
wake up and complete link training in less than 100 ms while the Cyclone V device completes loading the
programming file for the rest of the device.

In addition, the Cyclone V device PCIe Hard IP has improved end-to-end datapath protection using error
correction code (ECC).

Transceiver Protocol Configurations in Cyclone V Devices

Altera Corporation

Send Feedback

CV-53004

PCI Express

4-2

2013.10.17

«
...
382
383
384
385
386
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: XDS Pages: 99

Brand: Hal Communications Pages: 25

Brand: TC Electronic Pages: 174

Finalizer Express

Brand: TC Electronic Pages: 33

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

Brand: Dialogic Pages: 2

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

Brand: EVOC Pages: 57

Brand: Arduino Pages: 25

SRA311-008P8 Series

Brand: Divio Pages: 4

Brand: Renesas Pages: 4

J-Link-OB-STM32F072-128KB

Brand: Segger Pages: 18

CHEETAH ST34501FC

Brand: Seagate Pages: 68

iMarc SLV 9820-2M

Brand: Paradyne Pages: 24

Brand: Lucent Technologies Pages: 7

ReadyNAS Duo v2

Brand: NETGEAR Pages: 100

Brand: ICP DAS USA Pages: 60

Brand: b&t Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands