manualshive.com logo in svg

Altera Cyclone V, Device Handbook

Looking for a detailed Boot Manual for the Altera Cyclone V? Look no further! Download our comprehensive manual for free from manualshive.com to unlock the full potential of this cutting-edge product. Discover step-by-step instructions, troubleshooting tips, and much more, all at your fingertips. Get your manual today!

Share
Download
background image

DQ/DQS Groups in Cyclone V ST

Table 6-10: Number of DQ/DQS Groups Per Side in Cyclone V ST Devices

This table lists the DQ/DQS groups for the soft memory controller. For the hard memory controller, you can get the
DQ/DQS groups from the pin table of the specific device. The numbers are preliminary before the devices are
available.

x16

x8

Side

Package

Member Code

2

5

Top

896-pin FineLine BGA

D5

D6

0

3

Right

3

10

Bottom

Related Information

Cyclone V Device Pin-Out Files

Download the relevant pin tables from this web page.

External Memory Interface Features in Cyclone V Devices

The Cyclone V I/O elements (IOE) provide built-in functionality required for a rapid and robust
implementation of external memory interfacing.

The following device features are available for external memory interfaces:

• DQS phase-shift circuitry
• PHY Clock (PHYCLK) networks
• DQS logic block
• Dynamic on-chip termination (OCT) control
• IOE registers
• Delay chains
• Hard memory controllers

UniPHY IP

The high-performance memory interface solution includes the self-calibrating UniPHY IP that is optimized
to take advantage of the Cyclone V I/O structure and the Quartus II software TimeQuest Timing Analyzer.
The UniPHY IP helps set up the physical interface (PHY) best suited for your system. This provides the total
solution for the highest reliable frequency of operation across process, voltage, and temperature (PVT)
variations.

The UniPHY IP instantiates a PLL to generate related clocks for the memory interface. The UniPHY IP can
also dynamically choose the number of delay chains that are required for the system. The amount of delay
is equal to the sum of the intrinsic delay of the delay element and the product of the number of delay steps
and the value of the delay steps.

The UniPHY IP and the Altera memory controller MegaCore

®

functions can run at half the I/O interface

frequency of the memory devices, allowing better timing management in high-speed memory interfaces.
The Cyclone V devices contain built-in circuitry in the IOE to convert data from full rate (the I/O frequency)
to half rate (the controller frequency) and vice versa.

External Memory Interfaces in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52006

DQ/DQS Groups in Cyclone V ST

6-12

2014.01.10

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Brand: e-con Systems Pages: 9
RAK RAK3372 Quick Start Manual preview
RAK3372
Brand: RAK Pages: 30
Renesas RL78/G1H User Manual preview
RL78/G1H
Brand: Renesas Pages: 941
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
EK EK-Quantum Momentum ROG Rampage VI Encore User Manual preview
EK-Quantum Momentum ROG Rampage VI Encore
Brand: EK Pages: 11
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
Black Box Secure Site Manager 16 Quick Start Manual preview
Secure Site Manager 16
Brand: Black Box Pages: 16
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Brand: Taiwan Commate Computer Inc. Pages: 25
Greenlee 910FS Instruction Manual preview
910FS
Brand: Greenlee Pages: 52
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Brand: uneron Pages: 13
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
Ross ULTRIX-FM-NS-1RU Install Manual preview
ULTRIX-FM-NS-1RU
Brand: Ross Pages: 5
AMD -K6-2/450 - MHz Processor Application Note preview
-K6-2/450 - MHz Processor
Brand: AMD Pages: 98
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18

Brands by name

Popular brands

Load more brands