Altera Cyclone V Device Handbook Download Page 1026 | Manualshive

Page: 1026 / 1077

background image

Related Information

Qsys Interconnect and System Design Components

For more information about the address span extender, refer to

Bridges

in the

Qsys

Interconnect and System

Design Components chapter in the

Quartus

®

II

Handbook.

Generating and Compiling the HPS Component

The process of generating and compiling an HPS design is very similar to the process for any other Qsys
project. Perform the following steps:

1. Generate the design with Qsys. The generated files include an .sdc file containing clock timing constraints.

If simulation is enabled, simulation files are also generated.

2. Add system.qip to the Quartus II project. system.qip is the Quartus II IP File for the HPS component,

generated by Qsys.

3. Perform Analysis and Elaboration with the Quartus II software.
4. Assign constraints to the SDRAM component. When Qsys generates the HPS component (step 1), it

generates the pin assignment Tcl Script File (.tcl) to perform memory assignments. The script file name
is <qsys_system_name>_pin_assignments.tcl, where <qsys_system_name> is the name of your Qsys
system. Run this script to assign constraints to the SDRAM component.

For information about running the pin assignment script, refer to “MegaWizard Plug-In Manager
Flow” in the

Implementing and

Parameterizing Memory IP chapter in the

External Memory

Interface Handbook

.

Note:

You do not need to specify pin assignments other than memory assignments. When you configure pin
multiplexing as described in

Configuring Peripheral Pin Multiplexing

, you implicitly make pin assignments

for all HPS peripherals. Each peripheral is routed exclusively to the pins you specify. HPS I/O signals are
exported to the top level of the Qsys design, with information enabling the Quartus II software to make
pin assignments automatically.

You can view and modify the assignments in the Peripheral Pin Multiplexing tab. You can also view
the assignments in the Quartus fitter report.

5. Compile the design with the Quartus II software.
6. Optionally back-annotate the SDRAM pin assignments, to eliminate pin assignment warnings the next

time you compile the design.

Related Information

•

Configuring Peripheral Pin Multiplexing

on page 27-5

•

Creating a System with Qsys

For general information about using Qsys, refer to the

Creating a System with Qsys

chapter in the

Quartus

®

II

Handbook.

•

Implementing and Parameterizing Memory IP

The Implementing and Parameterizing Memory IP

chapter in the

External Memory Interface

Handbook.

•

Specifying HPS Simulation Model in Qsys

on page 29-10

For a description of the simulation files generated, refer to "Simulation Flow" in the Simulating the HPS
Component chapter of the

Cyclone V Device Handbook, Volume 3

.

Altera Corporation

Instantiating the HPS Component

Send Feedback

27-11

Generating and Compiling the HPS Component

cv_54027
2013.12.30

«
...
1024
1025
1026
1027
1028
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: Garland Pages: 4

CLICK PLUS C2-02CPU

Brand: Automationdirect.com Pages: 10

Brand: Alesis Pages: 61

Brand: EVS Pages: 30

Brand: SIIG Pages: 6

Brand: Crystal Vision Pages: 54

Brand: ICP DAS USA Pages: 31

Brand: Xilinx Pages: 27

Brand: Netopia Pages: 138

Brand: PACOM Pages: 16

Brand: Zmotion Pages: 56

Brand: StarTech.com Pages: 8

Brand: StarTech.com Pages: 13

Schottky Barrier Diodes MA3XD21

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA2SE01

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA2SD32

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA2Z720

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA3X727 (MA727)

Brand: Panasonic Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands