Home
/
Altera
/
Cyclone V
/
Device Handbook

Altera Cyclone V, Device Handbook

Share

Page: 270 / 1077

Altera Cyclone V Device Handbook Download Page 270

• To perform BST during configuration, issue

CONFIG_IO

JTAG instruction to interrupt configuration.

While configuration is interrupted, you can issue other JTAG instructions to perform BST. After BST is
completed, issue the

PULSE_CONFIG

JTAG instruction or pulse

nCONFIG

low to reconfigure the device.

The chip-wide reset

(DEV_CLRn)

and chip-wide output enable

(DEV_OE)

pins on Cyclone V devices do not

affect JTAG boundary-scan or configuration operations. Toggling these pins does not disrupt BST operation
(other than the expected BST behavior).

If you design a board for JTAG configuration of Cyclone V devices, consider the connections for the dedicated
configuration pins.

Do not cascade JTAG chains for FPGA and HPS together when you are performing BST. The JTAG
for HPS does not support BST.

Note:

Related Information

•

Cyclone V Device Family Pin Connection Guidelines

Provides more information about pin connections.

•

Configuration, Design Security, and Remote System Upgrades in Cyclone V Devices

Provides more information about JTAG configuration.

•

Cyclone V Device Datasheet

Provides more information about JTAG configuration timing.

Enabling and Disabling IEEE Std. 1149.1 BST Circuitry

The IEEE Std. 1149.1 BST circuitry is enabled after the Cyclone V device powers up. However for Cyclone V
SoC FPGAs, you must power up both HPS and FPGA to perform BST.

To ensure that you do not inadvertently enable the IEEE Std. 1149.1 circuitry when it is not required, disable
the circuitry permanently with pin connections as listed in the following table.

Table 9-4: Pin Connections to Permanently Disable the IEEE Std. 1149.1 Circuitry for Cyclone V Devices

Connection for Disabling

JTAG Pins

(23)

V

CCPD

supply of Bank 3A

TMS

GND

TCK

V

CCPD

supply of Bank 3A

TDI

Leave open

TDO

(23)

The JTAG pins are dedicated. Software option is not available to disable JTAG in Cyclone V devices.

JTAG Boundary-Scan Testing in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52009

Enabling and Disabling IEEE Std. 1149.1 BST Circuitry

9-8

2014.01.10

«
...
268
269
270
271
272
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands